The Job Dashboard gives you a complete financial picture of a job or phase in one screen, combining charts, tables and thermobars. Instead of searching through separate reports, you get quote value, invoicing, costs and profit all in one place, updated in real time as work happens.
This article explains what each panel on the Job Dashboard shows and how to read it.
Every job has its own dashboard, and you'll find the same view at phase level if you want to check the performance of one piece of work in isolation.
Opening the Job Dashboard
- Open the job (or phase) you want to check.
- Select the Dashboard tab.
The dashboard is made up of several tiles. You can drag any tile into a new position, so the information that matters most to you sits at the top of the screen.
Health check
The health check tile gives you an at-a-glance gauge of how close a job is to becoming unhealthy, using a series of thermobars.
- Invoiced to quoted: the quote value of the job, and what percentage of that has been invoiced so far.
- Recognised to invoiced / recognised to quoted: if revenue recognition is switched on, how much of the invoiced or quoted value has been recognised.
- Actual to estimated hours: actual hours recorded on timesheets compared to hours estimated overall.
- Recommended charge to invoiced: how much is recommended to be charged, based on timesheets at charge value plus marked-up purchases and expenses, compared to how much has actually been invoiced.
- Recognised to recommended charge: if revenue recognition is on, how much has been recognised compared to the recommended charge.
- Actual to estimated cost: costs incurred for time, purchases, expenses and materials, compared to what was originally estimated.
Key financials
This panel is a bar chart comparing estimated cost, quoted value, recommended charge value of time and purchases spent to date, invoiced value, and (if revenue recognition is switched on) recognised value. Hover over any bar for the exact figure.
It's the quickest way to see whether the charge value of time spent has overtaken the quoted value.
Once a job is closed, this panel also shows an over recovered or under recovered value. This is the difference between what Synergist recommends you charge and what you've actually invoiced, sometimes referred to as client investment.
Status
The status panel shows invoicing status and how much is left to bill.
- Remaining to invoice: quoted value less invoiced value. A negative figure means you've invoiced more than the quote.
- Completed: a soft close, set by the job handler via the Actions button. It stops any further time, materials, purchases or expenses being recorded against the job, and can be reversed. Completed jobs stay in Synergist but won't show on the default jobs list, so you'll need a filtered view to find them.
- Closed: a hard close, usually done by Finance, and not reversable. The only way to reopen a closed job is to create a new phase. Find out more about Closing a Job.
- Percentage completion: set manually by the job handler, so you can compare how complete the job really feels against what the health check panel is telling you. You can also set this in the Gantt view on the job or phase. It isn't calculated from any figures stored on the job.
Estimated to actual
This tile compares estimated and actual figures three ways. Use the drop-down in the panel header to switch between:
- Cost
- Hours
- Recommended charge
Hover over any column for an exact value.
Profit & costs
This panel gives you a side-by-side view of estimated and actual profit.
- Quote vs Estimate: gross and net profit based on the value quoted to the client against the costs estimated.
- Invoiced vs Actuals: gross and net profit based on the value actually invoiced/recognised against the actual costs incurred to date.
Switch between these using the drop-down in the panel.
Comparison to recommended charge
This panel shows recommended charge values for the job or phase, calculated by totalling time, purchases and expenses, and materials. It compares that total to either the quoted or invoiced amount, so you can see where discounts or uplifts have been applied.
Use the drop-down to switch between invoiced and quoted value, and to view either estimated or actual figures.
Allocated and unallocated costs
These two tiles show you where your costs sit in the billing process.
- Allocated costs: costs that have been ticked off against a sales invoice. The actual cost and recommended charge of these billed costs gives you a recommended profit figure, which is then compared to your actual profit.
- Unallocated costs: costs not yet ticked off against any sales invoice. These make up the basis of your work in progress (WIP) reports, and show the potential profit you'd make once they're billed.
Value (to date)
This tile breaks profit down by cost type, so you can see time, purchases and materials separately rather than as one combined figure. It also shows the mark-up percentage for each, making it easy to spot which cost type is dragging your overall mark-up down.
Chargeable time booked and unbooked
This displays total estimated time on the job/phase, shown as hours and recommended charge, split between time that's been booked and time that hasn't.
PO/PI control
This control changes how actual purchase costs are calculated across every panel on the dashboard. There are three settings:
- PO cost: uses purchase order values only. Purchase invoices are ignored.
- PO/PI cost: uses the purchase order cost, unless it's marked as final supplier invoiced, in which case the purchase invoice value is used instead.
- PI cost: uses purchase invoice amounts only, including both part and final invoices. Purchase order costs are ignored.
Tips
- Drag your most-used tiles to the top of the dashboard. Tiles can be reordered but not removed, so make the layout work for you.
- If a job hasn't been invoiced yet, switch the Profit & costs and Comparison to recommended charge panels to quoted value, so you're not looking at an empty comparison.
- Use the Estimated to actual panel in hours mode as your first check on whether a job is running over. It's the simplest signal before you dig into cost and charge figures.
- Check Allocated and Unallocated costs together. One shows profit already locked in, the other shows profit still to come once you invoice.
- Remember that Completed is reversible and stops new costs being added, while Closed is permanent and can only be undone by opening a new phase.